Sprinter 144 Ceiling Panel CNC DXF File, 2019+ High Roof (Digital Download)

Digital file download only

The black dots shown in the design indicate the mounting holes used to fasten the ceiling panels to the factory roof beams.

These mounting holes have been precisely positioned for CNC cutting, saving you hours of measuring, aligning, and drilling during installation. In my own Sprinter camper van build, I used M5 rivet nuts and M5 screws, which fit the factory mounting holes perfectly. This approach makes installation straightforward while minimizing the need to drill any additional holes.

The design file is provided as a clean template and does **not** include cutouts for ceiling lights, wiring slots, or the Maxxair fan, allowing you to customize the layout to suit your own van build.

If you would like the ceiling panels to match my van exactly as shown in the photos, feel free to reach out, and I'd be happy to provide that version of the design file.

Key Features & Benefits

✔ PRECISION-DERIVED DESIGN (NOT YET INSTALLED)
Developed based on a fully tested Sprinter 170 ceiling system and refined using precise measurements from a Sprinter 144. While not yet physically installed in a 144 build, the design reflects real-world geometry.

✔ ACCURATE CEILING CURVATURE MATCHING
Front sliding door curve and rear tailgate curvature are carefully modeled for a clean, factory-like fit.

✔ FACTORY STRUCTURE ALIGNED
OEM roof beam positions are mapped to match factory structure and simplify installation.

✔ PRE-PLANNED CEILING LIGHTING
Includes layout for 6 inch round LED ceiling light positions.

✔ BUILT-IN ELECTRICAL CONSIDERATION
Accounts for VAN GND (ground) reference point in the layout.

✔ MOUNTING POINTS PRE-PLANNED
Mounting locations are aligned with factory structure for secure fastening (final drilling required).

✔ L-TRACK READY DESIGN
Hidden mounting zones allow for clean L-track integration.

✔ VENT & LIGHTING READY
Pre-planned cut areas for roof fan (e.g., Maxxair) and lighting placement.

✔ MAXXAIR FAN COMPATIBLE
Roof vent cutout is designed to match standard Maxxair fan dimensions, making installation easier and more accurate.

✔ OPTIMIZED FOR 4×8 SHEETS
Efficient layout designed for standard sheet sizes to reduce material waste.

✔ VERIFY BEFORE CUTTING
Designed as a precise starting point, basic measurement and alignment checks are recommended before cutting.

Description

These DXF files are designed for a Sprinter 144 high roof ceiling panel system (2019+), developed using my proven Sprinter 170 ceiling design and adapted with accurate measurements from a 144 model.

The original 170 version has been fully tested in a real build. This 144 version follows the same design logic and structural alignment, but has not yet been physically installed in a Sprinter 144.

Many generic templates fail to properly account for the complex curvature of the Sprinter ceiling—especially around the sliding door and rear tailgate. This design was created to address those real-world challenges.

Every major structural element has been considered—including factory beams, mounting points, lighting layout, and accessory placement—so you can focus on building instead of troubleshooting.

DXF Files Included
Full ceiling panel layout (1 DXF file)

Notes & Important Details
This design follows factory roof beam layout, but small variations between vans may exist.

Minor trimming may be required depending on:
insulation thickness
ceiling finish materials
manufacturing tolerances

Mounting positions are pre-planned, but final drilling is left to the builder for flexibility.
Photos shown may reflect customized installations and may not exactly match the raw DXF files.
This design includes allowance for finishing materials (e.g., fabric wrapping), so slight spacing may exist by design.
Compatibility

Designed for:

Mercedes Sprinter 144 High Roof (2019+)

Not guaranteed for:

Pre-2019 models (possible dimensional differences)

Not intended for:

Sprinter 170
Sprinter 170 EXT
Other van platforms
Digital Download Only

This is a digital product only.
No physical items will be shipped.

Frequently Asked Questions (FAQ)

Q: Are these physical templates?
A: No. These are digital DXF files for CNC cutting.

Q: Has this been tested in a real Sprinter 144 build?
A: Not yet. This design is based on a fully tested Sprinter 170 system and precise 144 measurements, but has not been physically installed. Minor adjustments should be expected.

Q: Do I need a CNC machine?
A: Yes. These files are intended for CNC routers, laser cutters, or similar equipment.

Q: Will this fit perfectly without modification?
A: No. These files provide a precise starting point. Minor trimming and fitting are expected due to insulation, finishing materials, and van-to-van variation.

Q: Should I perform measurements before cutting?
A: Yes. Due to variations in insulation, framing, ceiling finish, L-track positioning, and factory tolerances, every van is slightly different. It’s important to verify key dimensions and alignment before cutting, and make minor adjustments as needed.

Q: Are mounting holes included?
A: Mounting positions are planned, but final drilling is left to the builder for flexibility.

Copyright & Usage

These files are for personal use only.

Not allowed:

Resale
Redistribution
Sharing
Use in commercial production